效劳热线：
15303929722
联系逐梦国际-梦想照进现实,起劲成绩未来!
公司名称：逐梦国际-梦想照进现实,努力成就未来!
电话：0392-3388939
传真：0392-3382020
联系人：周司理
手机：18803921757
联系人：赵司理
手机：15303929722
邮箱：hebiqitian@163.com
单位地点：河南省鹤壁市市辖区东杨工业园区香山路152号
微机灰熔点测定仪摄像头的调试要领
2025-12-17 来自: 逐梦国际-梦想照进现实,努力成就未来!. 浏览次数:203
Ash melting point camera debugging
装置好摄像头后，，，，，， ，摄像头距离灰熔点炉体的间距为150mm
After installing the camera, the distance between the camera and the ash melting point furnace body is 150mm
摄像头先容
Camera Introduction
摄像头三个旋钮调解，，，，，， ，以前到后作用划分是：
The three knobs of the camera are adjusted, and their effects from front to back are:
调解画面巨细
Adjusting the screen size
调解画面明暗
Adjusting the brightness of the screen
调解画面清晰度
Adjusting the clarity of the screen
画面调解
Screen adjustment
装备最先后，，，，，， ，温度抵达900℃时弹出提醒。。。。。不要点击对话框中的“知道了”，，，，，， ，这时最先调解摄像头。。。。。注重：调解速率要快，，，，，， ，装备到1000℃后系统会自动最先实验，，，，，， ，导致调解失效
After the device starts, a prompt will pop up when the temperature reaches 900 ℃. Don't click on "Got it" in the dialog box, then start adjusting the camera. Attention: The adjustment speed should be fast. After the device reaches 1000 ℃, the system will automatically start the experiment, causing the adjustment to fail
先调解画面焦距，，，，，， ，就是摄像头zui内侧的旋钮，，，，，， ，调解到样品边沿清晰即可。。。。。如下图
First adjust the focal length of the image, which is the innermost knob of the camera, until the sample edge is clear. As shown in the following figure
然后用摄像头中心谁人旋钮来调解画面的亮度，，，，，， ，不可太亮也不可太暗。。。。。如下图
Then use the knob in the middle of the camera to adjust the brightness of the image, which should not be too bright or too dark. As shown in the following figure
最后调解画面巨细�。。。。�，，，， ，用摄像头zui外侧的，，，，，， ，先将带编号的方框完整框住样品，，，，，， ，尖头部分不需要完全顶住“编号方框”的顶部。。。。。
Finally, adjust the picture size. Use the outermost part of the camera to completely frame the sample with the numbered box. The pointed part does not need to completely support the top of the "numbered box".
画面调解好之后点击弹出对话框中的“知道了”
After adjusting the screen, click "Got it" in the pop-up dialog box
然后用鼠标点击界面中的“原型”画面。。。。。
Then click on the "prototype" screen in the interface with the mouse.
点击过“原型”画面后，，，，，， ，系统会牢靠现在的亮度，，，，，， ，然后就算灰熔点测定仪摄像头调试完毕
After clicking on the "prototype" screen, the system will fix the current brightness, and then even after debugging is completed
详细详情可联系鹤壁逐梦国际-梦想照进现实,努力成就未来!公司举行咨询0392-3388939 3388929